allowable deformation中文是什么意思

• 容许变形

• "allowable"中文翻译    adj. 可容许的，可承认的，不碍事的，正当的。 Two ...
• "allowable subsoil deformation" 中文翻译 :    地基变形允许值
• "allowable" 中文翻译 :    adj. 可容许的，可承认的，不碍事的，正当的。 Two mistakes are allowable in this game. 这种游戏允许犯规两次。 adv. -bly
• "deformation" 中文翻译 :    变形,走样; 变形，变态，形变，畸形; 变形，失真; 变形；变态; 变形纹; 变形性; 地基应力和变形变形; 改丑; 畸型; 加工变形; 色泽牢固; 型变; 形变；变形; 形心; 应变
• "allowable acceleration" 中文翻译 :    容许加速度
• "allowable accelertion" 中文翻译 :    容许加速度
• "allowable amplitude" 中文翻译 :    容许振幅
• "allowable approximation" 中文翻译 :    容许近似值
• "allowable background" 中文翻译 :    容许本底水平
• "allowable band" 中文翻译 :    允许范围
• "allowable bearing" 中文翻译 :    容许承压力; 容许承载力; 容许支承力
• "allowable buckling" 中文翻译 :    容许扭曲应力
• "allowable capacity" 中文翻译 :    允许产能
• "allowable carrier" 中文翻译 :    容许载体量
• "allowable catch" 中文翻译 :    容许的捕鱼量; 容许的捕捉量; 许可渔获得; 许可渔获量
• "allowable clearance" 中文翻译 :    容许间隙; 允许间隙
• "allowable closure" 中文翻译 :    允许闭合差
• "allowable concentration" 中文翻译 :    容许浓度; 许容浓度; 允许浓度
• "allowable contact" 中文翻译 :    容许接触应力
• "allowable coordinates" 中文翻译 :    容许坐标
• "allowable cost" 中文翻译 :    可允成本; 允许成本
• "allowable costs" 中文翻译 :    可报销费用
• "allowable criterion" 中文翻译 :    容许标准 许容基准
• "allowable current" 中文翻译 :    容许电流; 允许电流
• "allowable cut" 中文翻译 :    容许采伐量

• Based on the experiment information and engineering application , the allowable deformation and cracked tensile force of the pipe joints are presented
  根据实验研究和工程实践，提出了用于供水管道抗震计算的管道接头允许位移和开裂拉力等参数。
• Using the optimum calculating method , some important technical parameters could be determined , that is , optimum supporting force , allowable deformation of rock mass , cross section area of u - shape set , pre - tight force and diameter of the bolt as well as torque to provide optimum supporting force
  用这一计算方法能求出岩石恒阻支护的重要技术参数，即最优（小）恒阻支护力、围岩最大允许变形量、恒阻u型钢支架的截面积、联接螺栓的预紧力和直径及最优支护力的拧紧力矩。
• In this paper , the cold die forging technology of the counter gear was analysed , the cold die forging was designed , the blank dimensions and the figure were calculated and choosed , the allowable deformation degree was checked , the equipment for the deformation was selected , the blank treatments before the cold die forging were draw up and the die structure of the cold die forging was designed
  分析了计数器齿轮的冷模锻工艺，设计了冷模锻件图，计算及选用了毛坯尺寸及形状，验算了许可变形程度，选择了变形用的设备，拟制了冷模锻前的毛坯处理及设计了冷模锻模具结构。
• Abstract : in this paper , the cold die forging technology of the counter gear was analysed , the cold die forging was designed , the blank dimensions and the figure were calculated and choosed , the allowable deformation degree was checked , the equipment for the deformation was selected , the blank treatments before the cold die forging were draw up and the die structure of the cold die forging was designed
  文摘:分析了计数器齿轮的冷模锻工艺，设计了冷模锻件图，计算及选用了毛坯尺寸及形状，验算了许可变形程度，选择了变形用的设备，拟制了冷模锻前的毛坯处理及设计了冷模锻模具结构。